User Tools
biac:experimentalcontrol:biac5hardware
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
biac:experimentalcontrol:biac5hardware [2021/08/05 14:34] cmp12 |
biac:experimentalcontrol:biac5hardware [2022/04/20 17:52] tbh6 |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| =====Hardware device connections at BIAC-5 3T (MR750) scanner===== | =====Hardware device connections at BIAC-5 3T (MR750) scanner===== | ||
| - | ==== BIAC5 3T -- Darwin computer==== | + | ==== Darwin computer ==== |
| Darwin is our primary stimulus presentation computer. | Darwin is our primary stimulus presentation computer. | ||
| Darwin has the following peripheral hardware connected: | Darwin has the following peripheral hardware connected: | ||
| Line 23: | Line 23: | ||
| * to reset AD device disconnect USB cable. | * to reset AD device disconnect USB cable. | ||
| * E-Prime dongle connected to USB port | * E-Prime dongle connected to USB port | ||
| - | * Scanner trigger cable connected via SRbox (code=16), and MeasComp analog (ch 5) and digital (B0) | + | * Scanner trigger cable connected via SRbox (code=16), and MeasComp analog (ch 5) and digital (B0), biopac analog CH 9 |
| * Scanner trigger is also connected to the MCC counter pin (CTR), this would show up as a number increase NOT a positive pulse | * Scanner trigger is also connected to the MCC counter pin (CTR), this would show up as a number increase NOT a positive pulse | ||
| * Biopac belt respiratory signal connected as MeasComp analog input (ch 0, w/ 1Kohm resistor), biopac analog ch4 | * Biopac belt respiratory signal connected as MeasComp analog input (ch 0, w/ 1Kohm resistor), biopac analog ch4 | ||
| * Biopac cardiac signal connected as MeasComp analog input (pulse ch3, OxSat ch4), biopac analog ( o2 ch3, pulse wave ch7, pulse rate ch11) | * Biopac cardiac signal connected as MeasComp analog input (pulse ch3, OxSat ch4), biopac analog ( o2 ch3, pulse wave ch7, pulse rate ch11) | ||
| * BioPac GSR signal connected as MeasComp analog input (ch 1) | * BioPac GSR signal connected as MeasComp analog input (ch 1) | ||
| - | * BioPac EGG signal connected as MeasComp analog input (ch 2) | + | * <del>BioPac EGG signal connected as MeasComp analog input (ch 2)</ |
| - | * Measurement Computing Box, DigPort-A0 Output to Analog Ch6 In, to BioPac Analog 8 input | + | * <del>Measurement Computing Box, DigPort-A0 Output to Analog Ch6 In, to BioPac Analog 8 input</ |
| * Measurement Computing Box, DigPort-A1 Output to Analog Ch7 In | * Measurement Computing Box, DigPort-A1 Output to Analog Ch7 In | ||
| ==== BIAC5 3T -- Kulpe computer==== | ==== BIAC5 3T -- Kulpe computer==== | ||
| - | Kulpe is our accessory computer. It is usually connected to the monitor on the right.\\ | + | Kulpe is |
| + | our accessory computer. It is usually connected to the monitor on the right.\\ | ||
| Kulpe has the following peripheral hardware connected: | Kulpe has the following peripheral hardware connected: | ||
| * Keyboard, video, and mouse connected to KVM video switch (CPU 3) | * Keyboard, video, and mouse connected to KVM video switch (CPU 3) | ||
biac/experimentalcontrol/biac5hardware.txt · Last modified: 2023/03/24 18:40 by cmp12
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
