Brain Imaging & Analysis Center

User Tools

Site Tools

You are here: biac » biac » experimentalcontrol » biac6hardware
biac:experimentalcontrol:biac6hardware

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
biac:experimentalcontrol:biac6hardware [2014/08/09 02:07]
favorini 		biac:experimentalcontrol:biac6hardware [2023/03/24 18:39] (current)
cmp12
Line 1: Line 1:
-=====Hardware device connections at BIAC-6 3T (New MR750) scanner=====+=====Hardware device connections at BIAC-6 3T (MR750) scanner=====
 ====BIAC6 3T -- Mach computer==== ====BIAC6 3T -- Mach computer====
 Mach is our primary stimulus presentation computer.  It is usually connected to the monitor on the left.\\ Mach is our primary stimulus presentation computer.  It is usually connected to the monitor on the left.\\
Line 7: Line 7:
   * Second monitor video output connected to video switch (CPU 2)   * Second monitor video output connected to video switch (CPU 2)
   * Stereo sound output to audio switch boxes   * Stereo sound output to audio switch boxes
 + 
   * Current Design 8-button serial response device (USB)   * Current Design 8-button serial response device (USB)
     * button box mode: "HHSC-2x4-C" response box     * button box mode: "HHSC-2x4-C" response box
     * button mode : "HID NAR 12345" (**003**)      * button mode : "HID NAR 12345" (**003**) 
       * must check this mode if power is cycled to the interface       * must check this mode if power is cycled to the interface
-  * MagConcepts Joystick (USB Gaming device)+  * Current Design 2 axis, 2 button joystick ( shared between 2 scanners ) 
 +    * autoconfigure 
 +    * HID Joystick 
 +    * USB - Tethyx 
 +    * after use switch back to button box with above settings 
 +  * Current Design Trackball 2 ( shared between 2 scanners ) 
 +    * autoconfigure 
 +    * HID HHSC-TRK-2 ( track 2 and comp seem to do the exact same thing ) 
 +    * roll ball around to calibrate 
 +    * after use switch back to button box with above settings 
 +  
 + 
   * E-Prime SR box (no button box, just scanner trigger) (COM1: 19200 baud, 8 bits, no parity)   * E-Prime SR box (no button box, just scanner trigger) (COM1: 19200 baud, 8 bits, no parity)
-  * Video switch serial cable on COM2+  * Video switch serial cable on **COM2**
   * Measurement Computing Analog/Digital data acquisition device (USB-1208FS, dev=0, 8 a/d chans)   * Measurement Computing Analog/Digital data acquisition device (USB-1208FS, dev=0, 8 a/d chans)
   * Serial cable to Donders on COM3 (e.g. ViewPoint eyetracker or Acknowledge)   * Serial cable to Donders on COM3 (e.g. ViewPoint eyetracker or Acknowledge)
   * E-Prime dongle (USB)   * E-Prime dongle (USB)
   * Scanner trigger cable connected as input to E-Prime SR box (code=16), and MeasComp analog (ADC3)   * Scanner trigger cable connected as input to E-Prime SR box (code=16), and MeasComp analog (ADC3)
-  * BioPac Respiratory belt signal connected as MeasComp analog input 0 (ADC0) +  * BioPac Respiratory belt signal connected as MeasComp analog input 0 (ADC0), biopac analog ch4 
-  * BioPac Cardiac signal connected as MeasComp analog input 1 (ADC1), biopac analog ( o2 ch2, pulse wave ch6, pulse rate ch10 ) +  * BioPac Cardiac signal connected as MeasComp analog input 1 (ADC1), biopac analog ( pulse wave ch6 ) 
-  * BioPac GSR signal connected as MeasComp analog input 2 (ADC2), biopack analog ch1 +  * BioPac GSR signal connected as MeasComp analog input 2 (ADC2), biopac analog ch1 
-  * Scanner trigger signal connected as MeasComp analog input 3 (ADC3)+  * Scanner trigger signal connected as MeasComp analog input 3 (ADC3), biopac analog ch9
   * Scanner trigger is also connected to the MCC counter pin (CTR), this would show up as a number increase NOT a positive pulse   * Scanner trigger is also connected to the MCC counter pin (CTR), this would show up as a number increase NOT a positive pulse
-  * <del>Measurement Computing Box, DigPort-A0 Output to BioPac Analog 8 input</del> + 
-  * BioPac STM100c: MCC DigPort-A0 output to BioPac digital i/o ch15\\ [[http://www.biopac.com/Manuals/mp_hardware_guide.pdf|biopac manual]] +
 ====BIAC6  3T -- Donders computer==== ====BIAC6  3T -- Donders computer====
 Donders is our accesory computer. It is usually connected to the monitor on the right.\\ Donders is our accesory computer. It is usually connected to the monitor on the right.\\
Line 43: Line 54:
   * Stereo sound jack for I-pod, MP3, etc connected to Audio switch (Aux - switch 4)   * Stereo sound jack for I-pod, MP3, etc connected to Audio switch (Aux - switch 4)
 ==== Video Switch Connections ==== ==== Video Switch Connections ====
 +
 +=== HDMI Video Switcher === 
 +[[biac:experimentalcontrol:hdmi|HDMI Video Switcher]]
 +
 === Source Devices === === Source Devices ===
   * CPU1 = Primary Display Computer (Mach), primary video output   * CPU1 = Primary Display Computer (Mach), primary video output
   * CPU2 = Primary Display Computer (Mach), secondary video output   * CPU2 = Primary Display Computer (Mach), secondary video output
   * CPU3 = Secondary/Eyetracker Computer (Donders)   * CPU3 = Secondary/Eyetracker Computer (Donders)
-  * CPU4 = Not connected +  * CPU4 = DVD Player 
-  * CPU5 = DVD player +  * CPU5 = Spare connection
-  * CPU6 = Not connected +
-  * CPU7 = Not connected +
-  * CPU8 = Not connected+
 === Output Devices === === Output Devices ===
   * OUT1 = Left Monitor   * OUT1 = Left Monitor
Line 57: Line 69:
   * OUT3 = Right Monitor   * OUT3 = Right Monitor
   * OUT4 = Projector   * OUT4 = Projector
-  * OUT5 = TV +  * OUT5 = Headphones 
-  * OUT6 = Not connected+  * OUT6 = 3D LCD
   * OUT7 = Not connected   * OUT7 = Not connected
   * OUT8 = Not connected   * OUT8 = Not connected
-=== Default Configuration "Stimulus to Subject" === + 
-Note: If you double-click the "Reset Video Switch" icon on the desktop, you will get the following configuration: +==== See also ==== 
-^ Source ^Output        ^Labels^ +  * [[http://www.mccdaq.com/usb-data-acquisition/USB-1208FS%20.aspx|USB-1208FS]] 
-|Mach 1 |Left Monitor  |CPU1 -> OUT1| +  * [[http://www.measurementcomputing.com|Measurement Computing Inc.]] 
-|Mach 2 |Middle Monitor|CPU2 -> OUT2| +  * [[http://www.measurementcomputing.com/PDFmanuals/sm-ul-user-guide.pdf|Universal Library User Guide]] 
-|Donders|Right Monitor |CPU3 -> OUT3| +  * [[http://www.biopac.com/Manuals/mp_hardware_guide.pdf|biopac manual]] 
-|Mach 1 |Projector     |CPU1 -> OUT4| + 
-|DVD    |TV            |CPU5 -> OUT5| +==== MCC digital channel to BIOPAC digital channel mapping ==== 
-|Mach 1 |No device     |CPU1 -> OUT6| +^MCC ^BIOPAC^ 
-|Mach 1 |No device     |CPU1 -> OUT7| +|  DA0 | “Trig” | 
-|Mach 1 |No device     |CPU1 -> OUT8|+|  DA1 |  D9 | 
 +|  DA2 |  D10| 
 +|  DA3 |  D11| 
 +|  DA4 |  D12| 
 +|  DA5 |  D13| 
 +|  DA6 |  D14| 
 +|  DA7 |  D15|
  
 [[biac:experimentalcontrol:biac5hardware|BIAC5 Scanner]]\\ [[biac:experimentalcontrol:biac5hardware|BIAC5 Scanner]]\\
 [[biac:experimentalcontrol:inventory|Back]] [[biac:experimentalcontrol:inventory|Back]]
  
biac/experimentalcontrol/biac6hardware.1407550078.txt.gz · Last modified: 2014/08/09 02:07 by favorini

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
CC Attribution-Share Alike 4.0 International Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki