User Tools
biac:experimentalcontrol:biac6hardware
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
biac:experimentalcontrol:biac6hardware [2016/09/07 13:23] cmp12 |
biac:experimentalcontrol:biac6hardware [2023/03/24 18:39] (current) cmp12 |
||
|---|---|---|---|
| Line 7: | Line 7: | ||
| * Second monitor video output connected to video switch (CPU 2) | * Second monitor video output connected to video switch (CPU 2) | ||
| * Stereo sound output to audio switch boxes | * Stereo sound output to audio switch boxes | ||
| + | |||
| * Current Design 8-button serial response device (USB) | * Current Design 8-button serial response device (USB) | ||
| * button box mode: " | * button box mode: " | ||
| * button mode : "HID NAR 12345" (**003**) | * button mode : "HID NAR 12345" (**003**) | ||
| * must check this mode if power is cycled to the interface | * must check this mode if power is cycled to the interface | ||
| - | * MagConcepts Joystick | + | * Current Design 2 axis, 2 button joystick |
| + | * autoconfigure | ||
| + | * HID Joystick | ||
| + | * USB - Tethyx | ||
| + | * after use switch back to button box with above settings | ||
| + | * Current Design Trackball 2 ( shared between 2 scanners ) | ||
| + | * autoconfigure | ||
| + | * HID HHSC-TRK-2 ( track 2 and comp seem to do the exact same thing ) | ||
| + | * roll ball around to calibrate | ||
| + | * after use switch back to button box with above settings | ||
| + | |||
| + | |||
| * E-Prime SR box (no button box, just scanner trigger) (COM1: 19200 baud, 8 bits, no parity) | * E-Prime SR box (no button box, just scanner trigger) (COM1: 19200 baud, 8 bits, no parity) | ||
| * Video switch serial cable on **COM2** | * Video switch serial cable on **COM2** | ||
| Line 20: | Line 33: | ||
| * BioPac Respiratory belt signal connected as MeasComp analog input 0 (ADC0), biopac analog ch4 | * BioPac Respiratory belt signal connected as MeasComp analog input 0 (ADC0), biopac analog ch4 | ||
| * BioPac Cardiac signal connected as MeasComp analog input 1 (ADC1), biopac analog ( pulse wave ch6 ) | * BioPac Cardiac signal connected as MeasComp analog input 1 (ADC1), biopac analog ( pulse wave ch6 ) | ||
| - | * BioPac GSR signal connected as MeasComp analog input 2 (ADC2), | + | * BioPac GSR signal connected as MeasComp analog input 2 (ADC2), |
| - | * Scanner trigger signal connected as MeasComp analog input 3 (ADC3) | + | * Scanner trigger signal connected as MeasComp analog input 3 (ADC3), biopac analog ch9 |
| * Scanner trigger is also connected to the MCC counter pin (CTR), this would show up as a number increase NOT a positive pulse | * Scanner trigger is also connected to the MCC counter pin (CTR), this would show up as a number increase NOT a positive pulse | ||
biac/experimentalcontrol/biac6hardware.1473254608.txt.gz · Last modified: 2016/09/07 13:23 by cmp12
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
