biac:experimentalcontrol:biac6hardware
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
biac:experimentalcontrol:biac6hardware [2016/09/07 13:23] – cmp12 | biac:experimentalcontrol:biac6hardware [2024/02/12 16:28] – cmp12 | ||
---|---|---|---|
Line 7: | Line 7: | ||
* Second monitor video output connected to video switch (CPU 2) | * Second monitor video output connected to video switch (CPU 2) | ||
* Stereo sound output to audio switch boxes | * Stereo sound output to audio switch boxes | ||
+ | |||
* Current Design 8-button serial response device (USB) | * Current Design 8-button serial response device (USB) | ||
* button box mode: " | * button box mode: " | ||
* button mode : "HID NAR 12345" (**003**) | * button mode : "HID NAR 12345" (**003**) | ||
* must check this mode if power is cycled to the interface | * must check this mode if power is cycled to the interface | ||
- | * MagConcepts Joystick | + | * Current Design 2 axis, 2 button joystick |
+ | * autoconfigure | ||
+ | * HID Joystick | ||
+ | * USB - Tethyx | ||
+ | * after use switch back to button box with above settings | ||
+ | * Current Design Trackball 2 ( shared between 2 scanners ) | ||
+ | * autoconfigure | ||
+ | * HID HHSC-TRK-2 ( track 2 and comp seem to do the exact same thing ) | ||
+ | * roll ball around to calibrate | ||
+ | * after use switch back to button box with above settings | ||
+ | |||
+ | |||
* E-Prime SR box (no button box, just scanner trigger) (COM1: 19200 baud, 8 bits, no parity) | * E-Prime SR box (no button box, just scanner trigger) (COM1: 19200 baud, 8 bits, no parity) | ||
* Video switch serial cable on **COM2** | * Video switch serial cable on **COM2** | ||
Line 20: | Line 33: | ||
* BioPac Respiratory belt signal connected as MeasComp analog input 0 (ADC0), biopac analog ch4 | * BioPac Respiratory belt signal connected as MeasComp analog input 0 (ADC0), biopac analog ch4 | ||
* BioPac Cardiac signal connected as MeasComp analog input 1 (ADC1), biopac analog ( pulse wave ch6 ) | * BioPac Cardiac signal connected as MeasComp analog input 1 (ADC1), biopac analog ( pulse wave ch6 ) | ||
- | * BioPac GSR signal connected as MeasComp analog input 2 (ADC2), | + | * BioPac GSR signal connected as MeasComp analog input 2 (ADC2), |
- | * Scanner trigger signal connected as MeasComp analog input 3 (ADC3) | + | * Scanner trigger signal connected as MeasComp analog input 3 (ADC3), biopac analog ch9 |
* Scanner trigger is also connected to the MCC counter pin (CTR), this would show up as a number increase NOT a positive pulse | * Scanner trigger is also connected to the MCC counter pin (CTR), this would show up as a number increase NOT a positive pulse | ||
Line 77: | Line 90: | ||
| DA6 | D14| | | DA6 | D14| | ||
| DA7 | D15| | | DA7 | D15| | ||
+ | |||
+ | |||
+ | ==== BIAC6 Screen Configuration ==== | ||
+ | * BIAC6 is equipped with NordicNeuroLab ( NNL ) [[https:// | ||
+ | |||
[[biac: | [[biac: | ||
[[biac: | [[biac: | ||
biac/experimentalcontrol/biac6hardware.txt · Last modified: 2024/07/15 13:39 by cmp12