biac:experimentalcontrol:biac5hardware
This is an old revision of the document!
Table of Contents
Hardware device connections at BIAC-5 3T (MR750) scanner
Darwin computer
Darwin is our primary stimulus presentation computer. It is usually connected to the monitor on the left.
Darwin has the following peripheral hardware connected:
- Keyboard, video, and mouse connected to KVM video switch (CPU 1)
- Second monitor video output connected to KVM switch (CPU 2)
- Stereo sound output to audio switch boxes (CPU1 - switch 1)
- E-Prime SRbox (COM1: 19200 baud, 8 bits, no parity)
- GE scanner cardiac/respiratory cable (COM4)
- Serial cable to Kulpe computer (COM3: 56K baud, 8 bits)
- Current Design 8-button serial response device (USB keyboard device, default mode)
- button box mode: “HHSC-2×4-C” response box
- button mode : “HID NAR 12345” (003)
- must check this mode if power is cycled to the interface
- Current Design 2 axis, 2 button joystick
- autoconfigure
- HID Joystick
- USB - Tethyx
- after use switch back to button box with above settings
- Current Design Trackball 2 ( shared between 2 scanners )
- autoconfigure
- HID HHSC-TRK-2 ( track 2 and comp seem to do the exact same thing )
- roll ball around to calibrate
- after use switch back to button box with above settings
- Measurement Computing Analog/Digital data acquisition device (USB-1208FS, dev=0, 8 a/d chans)
- to reset AD device disconnect USB cable.
- E-Prime dongle connected to USB port
- Scanner trigger cable connected via SRbox (code=16), and MeasComp analog (ch 5) and digital (B0), biopac analog CH 9
- Scanner trigger is also connected to the MCC counter pin (CTR), this would show up as a number increase NOT a positive pulse
- Biopac belt respiratory signal connected as MeasComp analog input (ch 0, w/ 1Kohm resistor), biopac analog ch4
- Biopac cardiac signal connected as MeasComp analog input (pulse ch3, OxSat ch4), biopac analog ( o2 ch3, pulse wave ch7, pulse rate ch11)
- BioPac GSR signal connected as MeasComp analog input (ch 1)
BioPac EGG signal connected as MeasComp analog input (ch 2)Measurement Computing Box, DigPort-A0 Output to Analog Ch6 In, to BioPac Analog 8 input- Measurement Computing Box, DigPort-A1 Output to Analog Ch7 In
BIAC5 3T -- Kulpe computer
Kulpe is
our accessory computer. It is usually connected to the monitor on the right.
Kulpe has the following peripheral hardware connected:
- Keyboard, video, and mouse connected to KVM video switch (CPU 3)
- BioPac communication (RJ45) cable
- Serial cable to Darwin computer (COM1)
BIAC5 3T -- Other devices
- DVD player connected to HDMI switch
Video Switch Connections
Source Devices
- IN1 = Primary Display Computer (Darwin), primary video output
- IN2 = Primary Display Computer (Darwin), secondary video output
- IN3 = Secondary/Eyetracker Computer (Kulpe)
- IN4 = DVD Player
- IN5 = Not connected
- IN6 = Not connected
- IN7 = Not connected
- IN8 = Not connected
Output Devices
- OUT1 = Left Monitor
- OUT2 = Middle Monitor
- OUT3 = Right Monitor
- OUT4 = Projector
- OUT5 = Headphones
- OUT6 = Not connected
- OUT7 = Not connected
- OUT8 = Not connected
MCC digital channel to BIOPAC digital channel mapping
MCC | BIOPAC |
---|---|
DA0 | “Trig” |
DA1 | D9 |
DA2 | D10 |
DA3 | D11 |
DA4 | D12 |
DA5 | D13 |
DA6 | D14 |
DA7 | D15 |
See also
biac/experimentalcontrol/biac5hardware.1679683238.txt.gz · Last modified: 2024/06/21 15:41 (external edit)